脉冲单频Nd:YVO4激光器及其倍频输出特性研究

为了研制激光干涉成像所需的主振荡功率放大(MOPA)结构脉冲单频激光器,本文完成MOPA激光器的种子源即声光调Q脉冲单频1 064 nm激光器的特性研究,同时完成种子源腔外倍频绿光特性研究。脉冲单频激光器采用声光调Q模块实现脉宽约20 ns的1 064 nm脉冲激光输出,采用环形腔设计并采用一组不同厚度的标准具实现单纵模运转。实验研究基频1 064nm和倍频532 nm激光脉冲的线宽,得出在全脉宽范围内都具有较高时间相干性的结论。实验分别获得脉宽约28 ns峰值功率约6.5 kW的1 064 nm脉冲单频激光和脉宽约20 ns、峰值功率约0.5 kW的532 nm脉冲单频激光,腔外倍频效率为5.6%。实验同时也验证了腔外倍频的激光脉宽压缩效应。     

A numerical algorithm for simulation of the Q-switched fiber laser using the travelling wave model

We develop a finite-difference scheme for approximation of a system of nonlinear PDEs describing the Q-switching process. We construct it by using staggered grids. The transport equations are approximated along characteristics, and quadratic nonlinear functions are linearized using a special selection of staggered grids. The stability analysis proves that a connection between time and space steps arises only due to approximation requirements in order to follow exactly the directions of characteristics. The convergence analysis of this scheme is done in two steps. First, some estimates of the uniform boundedness of the discrete solution are proved. This part of the analysis is done locally, in some neighborhood of the exact solution. Second, on the basis of the obtained estimates, the main stability inequality is proved. The second-order convergence rate with respect to the space and time coordinates follows from this stability estimate. Using the obtained convergence result, we prove that the local stability analysis in the selected neighborhood of the exact solution is sufficient.     

全固态单纵模脉冲Nd:YVO_4环形激光器

设计并研制了全固态调Q脉冲单纵模Nd:YVO4环形激光器。利用880nm激光二极管端面抽运Nd:YVO4晶体,通过四镜环形谐振腔中插入声光调Q晶体、标准具,并优化激光谐振腔的结构,获得了重复频率为200Hz、脉宽为26.6ns的单纵模脉冲1.064μm激光输出。当泵浦功率为15 W时,单纵模激光输出的单脉冲能量为570μJ、脉冲能量稳定性优于3%。     

电光调QCO2激光器的六温度模型理论与速率方程理论比较分析

分别利用速率方程理论和六温度模型理论对Q开关CO₂激光器动力学过程进行了理论分析比较,实验上测得电光调Q射频波导CO₂激光器脉冲激光建立时间及峰值功率与速率方程理论和六温度模型理论计算结果一致.但速率方程理论计算的激光脉冲宽度较“窄”,并且几乎没有拖尾,而六温度模型理论计算的脉冲激光波形有明显的拖尾,符合实际测量的波形.另外,六温度模型理论可以全面反映激光器工作气体中不同分子能级的能量转移过程,因此六温度模型理论分析更全面 关键词： 2激光器')" href="#">电光调QCO₂激光器 六温度模型理论 速率方程理论     

LD-pumped passively Q-switched Nd:YVO4 infrared and green lasers

A laser diode directly end-pumped, passively Q-switched Nd:YVO₄/Cr:YAG laser is presented in this paper. With 600 mW incident pump laser, Q-switched 1064 nm laser with an average power of 138 mW, pulse width of 19.8 ns, repetition rate of 170.1 kHz and peak power of 40.96 W is obtained. When a KTP crystal was inserted into the cavity, Q-switched 532 nm laser with an average power of 56 mW, pulse width of 28.4 ns, repetition rate of 118.2 kHz and peak power of 16.7 W is obtained at last.     

退压式La_3Ga_5SiO_(14)晶体电光调QNd∶YAG激光器激光性能研究

通过对硅酸镓镧(LGS)晶体旋光性与电光效应的交互作用的理论研究,推导出晶体旋光性和电光效应共同作用下的光强表示式I=1-4B2(Asin 2ω-Ccos 2ω)2。利用此表示式设计计算了旋光晶体LGS尺寸为8 mm×8 mm×25 mm电光Q开关在1064 nm波长使用时的开关电压和偏振角分别为4995 V和27.3°。将理论研究得到的结论应用于LGS晶体电光调Q的Nd∶YAG晶体激光器的实验研究中,实验结果与理论计算结果基本一致。得到输出能量为361 mJ,脉冲宽度为7.8 ns的脉冲激光输出。     

高脉冲重复频率调Q Tm,Ho:GdVO4激光器

报道了一个高效率连续波和调Q高重频两种运行方式的Tm,HoGdVO4激光器.Tm,HoGdVO4晶体尺寸4 mm×4 mm×7 mm,a轴通光,液氮制冷到100 K,由发射中心波长为793 nm的光纤耦合激光二极管端面泵浦.Tm,HoGdVO4激光连续波输出功率4.0 W,光光转换效率26%.声光调Q条件下输出平均高功率3.9 W,脉冲重复频率10 kHz,脉冲宽度50 ns. 通过减小声光Q开关的开启时间,激光脉冲宽度由50 ns减小至23 ns.在10 kHz重频下,测量最大脉冲能量0.39 mJ , 峰值功率7.8 kW.     

二极管激光侧泵浦单横模100Hz电光调Q激光器

介绍了二极管激光侧泵浦单横模１００Ｈｚ电光调Ｑ激光器的实验结果。泵浦源为一个线阵准连续１００Ｗ二极管激光器，激光工作介质为ＮｄＹＡＧ薄梯形板条，板条与泵浦源间用柱透镜耦合，ＫＤ＊Ｐ电光晶体调Ｑ。在１００Ｈｚ重复频率下，获得单脉冲能量２．３７ｍＪ，脉宽小于７ｎｓ，光束质量因子Ｍ２＝１．１的１．０６μｍ激光，光－光效率为８．５％，斜效率为１８．７％。     

氙灯泵浦的NYAB晶体调Q激光运转特性及实验研究

首次报道了氙灯泵浦的自激活自倍频NYAB复合功能晶体的BDN染料片调Q运转,获得了自倍频绿光单脉冲.测量了不同L和T_o情况下的绿光脉冲的能量、脉宽和峰值功率.文中还从理论上推导了自激活自倍频晶体调Q激光器的方程组.数值求解方程组,所得的理论数据与实验结果很好地相符.最后,讨论了进一步提高绿光脉冲峰值功率的途径.     

Laser induced copper electroless plating on polyimide with Q-switch Nd:YAG laser

The results of laser induced deposition of copper on polyimide substrate from copper electrolyte solution are reported. Unlike most work reported in the literatures where CW Ar⁺ lasers were used, a second harmonic (532 nm wavelength) Q-switch Nd:YAG laser was used for our experiments. The deposition process was conducted by laser-catalyzing of the polyimide surface and subsequent photothermal-accelerated reduction of copper-complex ions in an alkaline reducing environment. The characteristics of the deposited copper line were investigated in terms of laser beam scanning speed, and the number of scans. The surface morphology and chemical composition of the deposited copper were analyzed using field emission scanning electron microscope (FESEM) and energy dispersive spectrometer (EDX). The optimum processing conditions have been identified. The copper deposit was found to adhere well to the substrate.